BATTLECRUISER 3000AD v2.0x TROUBLESHOOTING FAQ
UPDATED: 12-24-00
BC3K V2.0x INSTALLATION & UPGRADING PROBLEMS
Q. WHY WHEN I PUT THE CD-ROM IN THE DRIVE, THE GAME WON'T INSTALL?
A. You may have AUTORUN disabled. Run the SETUP.EXE program from the BC3K CD-ROM by going to the
START button, selecting RUN and then typing D:\SETUP and hitting ENTER. Substitute the letter
D for your actual CD-ROM drive letter. To find this out, open up MY COMPUTER on your
desktop. You can also install by double-clicking on your CD-ROM icon in MY COMPUTER and then
double-clicking on the SETUP icon.
Q. AFTER I INSTALL AND TRY TO PLAY, I GET "FATAL ERROR, PTE MFSfopen" ERROR, WHY?
A. You will only get this error if you did not adhere to the warning in the README.TXT file that
is displayed prior to installation. You should NOT install the game to a folder that has more
than 8 characters in the name. C:\BATTLECRUISER in incorrect, C:\GAMES\BC3000AD OR SIMILAR, IS
OK. When in doubt, use the default, C:\BC3000AD
Q. AFTER I INSTALL AND TRY TO PLAY, I GET KICKED BACK TO THE DESKTOP WITH AN ERROR, WHY?
A. See the answer above. Also, make sure that you have downloaded and properly installed the
latest patch for the game.
Also, edit the shortcut properties for the BC3K or BC3K (3DFX) icon and disable the Close
On Exit box. Then save new shortcut settings. Now, when you run the game, if it quits, the
MS-DOS box will remain on the screen and you can see the error message. This will help you
determine what the problem is. Once you have resolved it, you can go back and tick that box
again to prevent it from being persistent when the game exits normally.
Q. HOW DO I RE-INSTALL AND START FROM SCRATCH?
A. Follow these steps to uninstall, reinstall and patch the game.
- Uninstall the current version of the game using the Add/Remove programs from Control panel.
- Use Windows Explorer and delete the BC3K install folder if it is not removed by the
uninstaller.
- Use Windows Explorer and check for the BC3K.INI file in the C:\WINDOWS folder and delete it.
BC3K checks for this file and if found, the setup program will not automatically start if you
have AUTORUN enabled. NOTE: If you are upgrading from v1.0x to v2.0x, this file will not exist.
- Run the SETUP.EXE program from the CD-ROM or, if you have AUTORUN enabled, eject the CD-ROM
and put it back in. Once install starts, make sure you READ the notice on the screen,
especially with regards to the install folder name. Do NOT select the CUSTOM install!
NOTE: If you missed the noticed, the file is called README.TXT and is located in the BC3K folder.
Use Notepad to read it or select its icon in the BC3K group created by the setup program.
- If you have a 3DFX Vooodoo card, download the Voodoo drivers on our site and read the
READTHIS.TXT file for instructions on how to install them. We have tested these drivers and
verified that they work with BC3K. You will be installing these in the BC3K folder, therefore,
they won't affect your other games. NOTE: Be sure to install the proper driver for your card.
- Setup your sound card using the Sound Setup icon in the BC3K icon group created by the
setup program.
- Run the game. Once you have verified that it runs fine, you can quit and then apply the Map
Pak and any cheats that you have downloaded. NOTE: Be sure to read the instructions for each!.
If you have any startup problems, then read the rest of this document for video, sound and
joystick and other configuration tips.
Q. I DOWNLOADED A PATCH, HOW DO I INSTALL IT?
A. Follow these steps to download and install the latest patch.
- Go to the file download area and get the latest patches. If this is the first time that you
are applying a patch, then download the single patch which will patch the boxed v2.0x directly to
the current version. Look for this first before you start downloading the incremental patches and
always read the file descriptions before downloading! Also, if you had tried to patch and
made a mistake, you are advised to uninstall and re-install the game, then try to re-apply the
patch.
- To download the patch, right-click on the file and select Save Target As to save it to
your BC3K install folder, i.e, C:\BC3000AD. If you download it to your Desktop or elsewhere on
your hard drive, you must move it into the folder where BC3K is installed, before running
it.
The current version is v2.09. So, if you have v2.0, you would first go from v2.0 to v2.08, then
v2.08 to v2.09. Those files are as follows. They must be installed in this order.
Also note that though the box may say v2.0, it may contain v2.07 because the game has had several
manufacturing runs. The setup screen will always indicate the version that you have.
If you have v2.0, grab these two. Right-click to download.
v2.0 to v2.08
v2.08 to v2.09
If you have v2.07, grab these two. Right-click to download.
v2.07 to v2.08
v2.08 to v2.09
If you have v2.08, grab this one. Right-click to download.
v2.08 to v2.09
- After you have downloaded the patch, go to the WIN9x START bar and using the RUN command,
browse to your BC3K install folder. Look for the patch executable, i.e bc3k200-208.exe which you
downloaded. When you find the file, left-click on it, then select OPEN and then OK. This will
execute the file and start the patching process. It will then prompt you before it starts the
patch process. If it points to another location other than where the game is installed, this
means that the patch is not in the BC3K install folder. Move it there and start over.
- Repeat this step for any and all subsequent patches.
When the patch has completed updating your version and you have verified that the game works,
you can delete the patch executable you downloaded and applied, in order to save disk space.
If after applying the patch you find that you cannot run the game, even though a prior version
worked fine, try deleting the SETUP.CFG and JOYSTICK.SET files from the BC3K install folder. New
versions of these files will be created when the game starts.
All saved games prior to v2.08, are not backward compatible. So, unless you are upgrading from
v2.08 to a higher version, you cannot restore and play your saved games. Just delete your
older saved games from the SAVE/RESTORE screen.
If the patch aborts with a message about an old file not found or similar, this means that
(a) you downloaded the wrong patch or (b) you are applying a patch to an incorrect version of
the game installed on your hard drive (c) you are trying to patch the c:\windows\desktop
location where you downloaded the patch to.
Always read the Version Control file for update info after you have applied a patch. You
can read this file on your computer using netscape or internet explorer by starting the
browser and loading the file from your BC3K install folder. Always check for an updated
version at the website also.
GENERAL QUESTIONS
Q. WHY DOES THE GAME CRASH ON STARTUP OR WHEN I'M PLAYING OR TRYING TO SAVE A GAME?
A. There are several reasons why the game will crash.
- If it crashes with a memory allocation error, then, follow the steps below.
- If it crashes with an invalid exception on startup, check the video section.
- If it crashes with an invalid exception during gameplay, it could be any number of things.
So, what do you do?
- Make sure that you have installed it properly and if you downloaded the patches, that
they too are installed properly.
- Try to figure out why the game is crashing.
- Open the BC3K shortcut folder by going to START->PROGRAMS->BC3000AD
- Right-click on either the BC3K or the BC3K (3DFX) shortcut and select PROPERTIES
- Go to the PROGRAM tab and left-click in the CLOSE ON EXIT box to remove the tick mark
- Left-click on APPLY and then on OK
Now, when you run the game, as soon as it crashes, the MS-DOS box will remain on the screen
and you will be able to see the error. Once you have made a note of it, just close the
window as normal. Later when you have solved the problem, you can repeat the steps above to put
the tick mark back in the CLOSE ON EXIT box so that the window is removed when you have finished
playing.
- Make sure that you have enabled your system to allow expanded or extended memory. If so, you
should see the following (or similar) lines in your C:\CONFIG.SYS file. If not, you need to add
them in. You can do this by editing the file in NOTEPAD. If you are using another command
processor, for example 4DOS.COM, then edit that line accordingly.
DEVICE=C:\WINDOWS\HIMEM.SYS /NUMHANDLES=64 /VERBOSE
DEVICE=C:\WINDOWS\EMM386.EXE RAM VERBOSE
SHELL=C:\WINDOWS\COMMAND.COM /E:4096 /P
DOS=HIGH,UMB
FILES=50
BUFFERS=20
The objective is to try and free up as much memory in a DOS box as possible and to remove any DOS
drivers that are not required and which take up valuable conventional memory. You can find this
out by opening an MS-DOS session and typing MEM. Then, look at the value next to "LARGEST
EXECUTABLE PROGRAM SIZE" and make sure that it is more than or close to 600KB (614,400 bytes).
More is better.
Make sure that you are not loading any Mouse, CD-ROM or ASPI drivers in either your C:\CONFIG.SYS
or C:\AUTOEXEC.BAT files unless you are absolutely certain that your system needs those drivers
in order to operate properly. DOS specific drivers are not needed when running under Windows. If
you see items in these files that are not needed, simply put a REM and a space, in front of the
line, to comment it out.
WARNING:Do not go editing your system files unless you know what you are doing.
- Go into the properties of the BC3K and BC3K (3DFX) shortcuts and change the MS-DOS DPMI
memory from AUTO to 16384 if you have 32MB or less of total memory in your machine. If you get a
memory allocation error, then try increasing this number by 4096 until you stop getting the
error. This will force WIN9x to provide that much DPMI memory to the program. If you have more
than 32MB of RAM and a 3DFX Voodoo card, set it higher than 16384 (you can go as high as 65535)
or leave it at the default value of AUTO. Note: you can only set this value higher by typing in
the number because the drop down box will only go up to 16384.
- If you have a 3Dfx Voodoo card and the game won't run or when you launch you get a blank
screen or it crashes during heavy combat, explosions etc, refer to the video section. You may
need new drivers.
Q. WHY WON'T THE GAME RUN ON MY CELERON PROCESSOR!
A. If you are over-clocking your CPU or your Voodoo graphics card, there is a very good chance
that the game will not run or behave erratically. Do NOT overclock your CPU or Voodoo graphics
card.
Q. DOES BC3K v2.0x USE DIRECTX AT ALL?
A. No. However, the next titles in the series, starting from Battlecruiser Millennium, support DirectX.
Q. WILL BC3K v2.0x RUN UNDER OS/2, LINUX, WIN 2000 or WIN NT?
A. No. However, the next titles in the series, starting from Battlecruiser Millennium, will
run under WIN2K but not WIN NT.
Q. WILL BC3K v2.0x RUN UNDER WIN ME?
A. Probably not. And if you did get it to run, it is unsupported. Good luck trying to get it to work.
Q. WHY WON'T THE GAME RUN IN PURE DOS?
A. Because it does not. You must run it under WIN9x using the shortcut created by the setup
program.
Q. WHAT IS THE MAP PAK AND WHY DO I NEED IT?
A. It is a product enhancement introduced in the boxed v2.08 release. It was made available to
existing owners of v2.0x via download. This enhancement includes over 7000 planetary zones
for you to explore and destroy. If you have the boxed v2.08, it already includes this
enhancement. You can apply the MAP PAK to either the v2.08 or v2.09 patch downloads. Do not
apply it to the boxed v2.08!
Q. HOW CAN I READ AND PRINT THE ONLINE MANUALS?
A. You will have to install the Acrobat reader if it is not already installed. Go into the group
folder created by the BC3K setup program and run the icon called Install Acrobat v3.01.
Once installed, you can simply double-click on any of the manuals in order to read or print
them.
If you downloaded the updated manuals, unzip them in the DOCS folder of the BC3K install
folder and then change the shortcut settings (which probably points to the older version in
the DOCS folder in the BC3K install folder or the CD-ROM) to point to the new version on your
hard drive.
Q. THE GAME IS TOO DIFFICULT, WHERE DO I GET HINTS AND TIPS?
A. You can start by reading the manual and also by downloading the hints and tips file from the
website. To meet other players and trade hints and tips, visit the website COMMLINK forum.
A tutorial is in the works for now, visit the GALCOM ACADEMY.
Q. HOW CAN I TELL WHICH VERSION OF THE BOXED v2.0x I HAVE?
A. You can tell by looking at the version number displayed on the top left corner of the
blue install screen. Also, though the US Interplay v2.0 release says v2.0 on the box, there
have been several new production units manufactured. This means that though the box says
v2.0, the version on the CD-ROM could be v2.0, v2.07 or v2.08. However, if the box says v2.08,
then it will contain v2.08.
If you have already installed the game, check your BC3K install folder for this file. Use this
to determine which patch you need to download.
BC3000AD.DAT 2,159,806 09/03/99 02:08 (v2.08 CD-ROM version)
BC3000AD.DAT 2,081,798 05/10/99 02:07 (v2.07 CD-ROM version)
BC3000AD.DAT 1,978,078 08/03/98 02:00 (v2.00 CD-ROM version)
Q. WHAT IS THE DIFFERENCE BETWEEN THE BOXED v2.0 AND v2.08 VERSIONS?
A. The Interplay 12/98 US release only has the CD-ROM and a printed 40 page mini-manual. The full
manual and other appendix files, including the keyboard commands, are on the CD-ROM. You need
to install Adobe Acrobat (included on the CD-ROM) to read and print these documents.
The GTi 10/99 and the Jack Of All Games 02/00 releases, which will say v2.08 on the box, have
the CD-ROM, the full printed 142 page manual (including all galactic maps) and a printed
keyboard sheet. It also has the full manual and other appendix files, on the CD-ROM. The
printed manual is accurate for v2.08 but a few changes which were made after the manual went
into production, are documented in the README.TXT file which is displayed during the
installation. This file also resides in the BC3K install folder once the installation has
completed. Further, the v2.08 release has the Map Pak planetary enhancements which include
over 7000 planetary zones.
The boxed v2.08 is not available for sale in the US, therefore, if you want to buy this
version in order to get the full printed materials, you will have to order it from the UK by
going to GTi Site where it is available. 3000AD no longer offers printed v2.0 manuals or
maps for sale.
VIDEO CARD PROBLEMS
WARNING!!!
- To those of you using utilities such as TweakIT! This utility writes settings into your
registry which could either damage your card or cause it to malfunction. You have been warned.
- Overclocking your 3dfx card can and will prevent BC3K from running. Keep the card at the
default clock speed.
Q. I HAVE A GRAPHICS CARD AND A 3DFX CARD, BUT THE GAME ONLY DETECTS THE MAIN GRAPHICS CARD!
A. BC3K will only detect the 2D chipset on the primary card, whether you have 1 or 2 graphics cards.
If you have, say, an nVidia TNT card and a 3DFX Voodoo II card, the second card is the card that
will be used for 3D graphics. The nVidia card is used for 2D graphics (menus etc). So, even if
you run the 3DFX version of the game, it will still detect the TNT card but will use the Voodoo II
card when it needs to use it in the 3D world.
Q. WILL THE GLIDE WRAPPER FOR MY NVIDIA CARD, WORK WITH BC3K?
A. No. BC3K uses DOS Glide, those wrappers require WIN Glide.
Q. WHAT 3DFX VOODOO CARDS DOES BC3K v2.0x SUPPORT?
A. BC3K v2.0x only supports 3D acceleration using any Voodoo graphics card such as Voodoo, Voodoo
Rush, Voodoo 2, Voodoo Banshee and Voodoo 3. Please ensure that you have the latest drivers
for your card! Your card driver install library MUST have installed the GLIDE2X.OVL file in
the C:\WINDOWS folder. If this file is not there, then the 3Dfx mode will NOT run and you
should then check your driver files or contact your card vendor.
If you are running the 3Dfx version using the shortcut, the BC3K3DFX.BAT file contains
environment settings for the Voodoo line of cards. Some machines may run out of environment
space as a result of these settings. If you encounter an 'out of environment space' message
due to the number of commands in the BC3K3DFX.BAT file, then go into the MEMORY settings for
the BC3K3DFX shortcut and change the 'Initial Environment' from AUTO to 4096 or higher.
If you are running the 3DFX version, make sure your desktop color depth is set to 16-Bit hi
color mode.
Q. MY COMPUTER SAYS THAT I HAVE A 3D OR 3DFX CARD INSTALLED BUT BC3K WON'T RUN
A. Many newbie gamers don't know that a 3D card is not the same as a 3DFX card. A 3DFX card is a
specific brand manufactured by 3DFX (www.3dfx.com) and it includes the Voodoo, Voodoo2, Voodoo
Rush, Voodoo Banshee and Voodoo3. Unless your manufacturer tells you that your 3D card is one
of these, it is not a 3DFX card. Several companies include Diamond, STB, Canopus, Creative
Labs and others, manufacture cards based on the 3DFX chipset. Manufacturers that use 3DFX
based graphics cards in their high-end systems, include Gateway, Compaq and several others.
Q. MY COMPUTER SAYS THAT I HAVE AN nVIDIA (OR OTHER) 3D CARD, SO DOES THIS MEAN I CAN'T RUN 3DFX?
A. Yes, that is exactly what it means. You should run the software version of the game, using the
normal BC3K icon created by the SETUP program, instead of the BC3K (3DFX) one. It will
not be as fast or look as pretty as when running under 3DFX, but at least you will get to play
the game.
The next titles in the BC3K series, due out in 2000, will have support for all 3D cards via
DirectX and OpenGL and as such, will support all DirectX compatible 2D/3D cards and not just
3DFX.
Q. WHY IS THE VIDEO CORRUPT OR I GET A CRASH TO DESKTOP WHEN I START THE GAME?
A. If after you install the game you get a General Protection Fault when you try to run it or you
are booted back to the desktop, you may have to configure BC3K to use your video card. But
first, download and install the latest patch which fixes some problems with the newer graphics
cards. If that does not fix it, continue reading.
If you have a 3DFX Voodoo3 video card, read the section below which deals with these cards.
Also, some cards such as the Intel i740, i810 and some ATI cards are unable to init in 640x480
16-bit color mode, which is what the BC3K Main Menu image uses at startup. In this case, you
have to contact your card vendor and probably get a BIOS upgrade. Or you could try using the
Sci-Tech Display Doctor. If you are using SDD, you would have to use the /v1 parameter to
start the game because it is a utility that gives a video card fast VESA capabilities. See the
sections below for more on this. Try adding /v1 parameter to the BC3K.BAT file first, before
attempting to install SDD!!
Q. HOW DO I FIND OUT IF BC3K SUPPORTS MY 2D CARD'S CHIPSET IN NATIVE MODE?
A. If your 2D card is in the list of native mode supported BC3K cards, then you can edit the
BC3K.BAT and BC3K3DFX.BAT files in NOTEPAD and add the /v? switch. Where the ? corresponds to the
number of your video card as listed in the table.
If you don't know what your card's chipset is, then proceed to the next step.
- Download the CHIPSET INFO utility from the 3000AD website and run it. This utility will
attempt to detect your video card chipset and display the results in a window. Below is a sample
output.
SVGA chipset: 3Dfx Voodoo Banshee / Voodoo3 (71)
video memory: 8192 KB
The number in the parenthesis (71) indicates the chipset number used by BC3K. This means that you
can add /v71 in the BC3K.BAT and BC3K3DFX.BAT files, or, you can just let BC3K auto-detect the
chipset. So, the execution line (the last line in the file) will look like bc3000ad /v71
Whatever chipset this utility detects is what BC3K will also auto-detect too. And as long as your
card chipset is auto-detected accurately, there is no need to edit the BC3K.BAT and BC3K3DFX.BAT
files.
If your card is detected as VESA, this means that the chipset is not supported directly by BC3K
or, the auto-detect is failing (Savage 4 cards for instance). In which case VESA 2.0 or 3.0
emulation (which is usually slower than using the native chipset) will be used instead of native
mode. In the case of Savage 4 cards, if the BC3K.BAT file does not contain /v1 and the graphics
are corrupt, then add it manually, by opening up the file in Notepad.
- Most new cards on the market support VESA 2.0/3.0, so you can use the default /v1 parameter
without requiring an external VESA driver. However, if that does not work, then you will have
to install a VESA 2.0/3.0 compliant driver. If BC3K cannot auto-detect the chipset or if it is
not supported in native mode, it will default to VESA mode. You can also force VESA mode by
adding the /v1 switch to the BC3K.BAT and BC3K3DFX.BAT files.
If you don't have a VESA driver for your graphics card or your driver does not work with the
game when the default auto-detect VESA mode (or /v1 parameter) is used, then try the Sci-Tech
Display Doctor available on the BC3K v2.0 CD-ROM. Go into the group folder created by the BC3K
setup program and run the icon called Install Display Doctor v6.53. Once installed, it
will provide your 2D graphics card with VESA 2.0/3.0 capabilities allowing you to run BC3K in
VESA mode.
If Display Doctor works for this game and it solves compatibility problems for you, then you
may want to continue using it for this and other games. To register your copy, follow the
instructions on the screen during the installation process. You can also go to the official
Display Doctor website.
You do NOT need to install the Sci-Tech Display Doctor unless you are having problems
with the 2D graphics mode or you have an older graphics card that does not have VESA 2.0 or 3.0
support built-in. You have been warned!
NOTES:
- Regardless of how much memory your 2D card has, BC3K will only report the first 8MB
- The 2D chipset will be used for all 2D operations and if you don't have a 3DFX card installed
the software renderer will also use this chipset. If you have a 3DFX card installed, then the
3DFX Glide renderer will be used for the 3D world rendering instead of the software renderer.
This is much faster and looks a whole lot better (see the screen shots page).
Q. WHY DOES THE GAME NOT WORK WITH MY i740 BASED CARD?
A. Depending on the BIOS version, you definitely need to install the Sci-Tech Display Doctor.
There are reports of screen corruption with v2.01 and higher due to the new 16-Bit Main Menu
graphic introduced in v2.01. It seems as if there is something wrong with VESA support on this
chipset.
Q. WHY DOES THE GAME NOT WORK WITH MY SAVAGE 3/4 BASED CARD?
A. If you have a card based on these chipsets, i.e, the Creative Labs card, then, you will have
to use either /v1 or /v57. Edit the BC3K.BAT and BC3K3DFX.BAT files in NOTEPAD and add this
parameter. Try /v57 first. So, the execution line (the last line in the file) will look like
bc3000ad /v57. If that doesn't work, try disabling the intro movie by adding /n
parameter. The intro movie player uses a different VESA driver detection method. So, you may
find that though the intro won't play, the game itself will run once you get past this problem.
Q. WHY DO I GET A '3DFX HARDWARE INIT FAILED' MESSAGE?
A. Could be a driver problem. If you don't have a Voodoo 3DFX based video card, do not start the
game with the BC3K (3DFX) icon. If you do have a Voodoo 3DFX based video card, then
read the following sections.
Q. WHY DOES THE GAME NOT WORK WITH MY VOODOO3 OR VOODOO BANSHEE BASED CARD?
A. The Voodoo3 uses the same drivers as the Banshee. However, the GLIDE2X.OVL which shipped with
this card, as well as the lastest driver set released by 3Dfx do not work with most
games that require GLIDE2X.OVL. You can download the VOODOO Drivers file from the 3000AD
website and unzip it into the folder where you installed BC3K. Read the included READTHIS.TXT
file. The game will then use this driver instead of the faulty one in C:\WINDOWS (which may
be needed by other games). This archive contains drivers for all 3DFX Voodoo boards.
Q. I HAVE AN OBSIDIAN X24 CARD AND THE GAME IS PURPLE! WHATS WRONG?
A. Make sure you download and install the latest drivers. Then, put the following commands in
your AUTOEXEC.BAT or BC3K3DFX.BAT file and reboot the machine.
SET SSTV2_FT_CLK_DEL=5
SET SSTV2_TF0_CLK_DEL=7
SET SSTV2_TF1_CLK_DEL=7
SET SSTV2_SLIM_VIN_CLKDEL=3
SET SSTV2_SLIM_VOUT_CLKDEL=2
SET SSTV2_SLIS_VIN_CLKDEL=3
SET SSTV2_SLIS_VOUT_CLKDEL=2
Q. I HAVE A VOODOO5 CARD AND THE GAME WON'T RUN! WHATS WRONG?
A. It could be any number of things. First, check your AUTOEXEC.BAT file and see if the Voodoo5
driver setup program, added these lines. If these lines do not appear in the file, add them
to the bottom of the file, exactly as shown below. Just open the C:\AUTOEXEC.BAT file
in Notepad, then cut these lines from this document, paste them into the file and save it.
REM == Voodoo legacy support for older games ==
@SET SST_GRXCLK=90
@SET SST_FT_CLK_DEL=0x4
@SET SST_TF0_CLK_DEL=0x6
@SET SST_TF1_CLK_DEL=0x6
@SET SST_VIN_CLKDEL=0x1
@SET SST_VOUT_CLKDEL=0x0
@SET SST_TMUMEM_SIZE=2
Check to make sure you did not change any of the default Voodoo settings in the original
BC3K3DFX.BAT file included by the v2.08 or v2.09 patch. If you did, download the default
file here into your BC3K folder, overwriting the current version in there. If you previously required
the /n or /v settings in your previous version of this file, then edit the file in Notepad. When
you are done with the editing of these files, reboot the computer and restart BC3K.
Once you've done that, look in C:\WINDOWS folder for the GLIDE2X.OVL file and copy it
to the folder where BC3K is installed. The only driver we have found to work, has the following
properties: GLIDE2X.OVL 235,263 05/04/2000 14:00. If yours is different and does not
work, then, download the VOODOO Drivers and in there you will find this driver in the VOODOO5.ZIP archive.
Simply unzip it into the folder where BC3K is installed.
Q. DOES BC3K v2.0x WORK WITH THE FSAA FEATURE OF MY VOODOO5 CARD?
A. Yes!
Q. WHY DO I GET A BLANK SCREEN OR A CRASH TO DESKTOP WHEN RUNNING THE 3DFX VERSION?
A. Several things could be happening. First, check these:
- First, ensure that your desktop screen color depth is set to 16-Bit Hi-Color
- If you have a 3DFX card, make sure that you have the latest Glide drivers (v2.43 or higher)
installed and then check for the GLIDE2X.OVL in your C:\WINDOWS or BC3K install folder. If this
file is not present, the 3Dfx mode will not work. Some cards, such as the Pure3D, do not install
this DOS Glide driver. You will have to locate it on the CD-ROM or get the latest version from
their website. You can also use the ones available on our website file downloads section.
- If you upgraded your 3D card and no longer have a Voodoo or Voodoo2 board on your machine,
then locate and rename the FXMEMMAP.VXD file located in the C:\WINDOWS\SYSTEM folder. This
applies to those of you upgrading to a Voodoo3 from a prior 3DFX Voodoo card.
- If you have a Voodoo2 card, check the applet and make sure that the clock rate is set to the
default.
- If you have multiple 3Dfx cards on your machine, you MUST ensure that the drivers installed
are the ones for the card you are using. For instance, if you have a Banshee and Voodoo2, the
game will use the GLIDE2X.OVL driver pertaining to the card it is supporting. Therefore, if you
add support for the Voodoo2 card as described above and the GLIDE2X.OVL file installed is for the
Banshee, you may experience problems. There is a Glide switcher over at the Creative Labs website
and other sites on the web, that you can use to switch between 3Dfx cards. You can also simply
copy the GLIDE2X.OVL for the particular card, into the BC3K folder and the game will use that
one, ignoring whatever version is in the C:\WINDOWS folder.
- Make sure you have Z-BUFFERING and TRIPLE BUFFERING disabled in your Voodoo 2 control panel.
If you don't have this utility, you can download it from www.3dfx.com. Once installed, use it to
disable these two settings and it may help solve the problem.
- From the PROPERTIES of the 'BC3K (3DFX)' shortcut, go into the MEMORY settings and change
the 'Initial Environment' from AUTO to 4096. If you get an 'out of environment space' memory
error at startup, increase this value slightly and in increments of 64 until the warning goes
away. You can remove the tick mark in the 'CLOSE ON EXIT' option of the shortcut in order to
see the error if the game exits with a problem.
Q. WHY IS THE SCREEN SO DARK UNDER 3DFX.
A. Use the ALT+, and ALT+. keys when you are in the cockpit of the craft to adjust the Gamma
settings. These are then saved in the SETUP.CFG file for later use by BC3K. The default
startup Gamma setting is 1.4 and the highest setting is 2.0.
SOUND CARD PROBLEMS
Q. WHY DON'T I GET ANY SOUND WHEN I RUN THE GAME?
A. Did you remember to run the SOUND SETUP program from the BC3K group folder of icons created
after the setup program completed? The v2.0 install program does NOT run this program
automatically when installation is completed. You should do this after installing by running
the Sound Setup shortcut created by the install program. This is documented in the README.TXT
file that is displayed by the setup program prior to installation.
Q. I SELECTED THE AUTO-DETECT OPTION IN THE SOUND SETUP PROGRAM AND IT HANGED MY SYSTEM!!
A. If the autodetect fails, then you need to find out what type of sound card you have installed.
Usually, this would be a Soundblaster or compatible sound card. Here's how to find out your
card settings.
FINDING THE SOUND CARD SETTINGS IF YOU DON'T KNOW THEM
- Go your CONTROL PANEL and select the SYSTEM icon.
- From the the DEVICE MANAGER tab, go down to the SOUND, VIDEO AND GAME CONTROLLERS tab and
press the + (plus) sign to reveal the devices under that tab.
- Look for your sound card, LEFT-CLICK to select it and then select the PROPERTIES tab.
- Go to the RESOURCES tab and look for the INPUT/OUTPUT RANGE, DIRECT MEMORY ACCESS and
INTERRUPT REQUEST settings on the left of that window. Make a note of the settings. Example
INPUT/OUTPUT RANGE : 0220-022F, DIRECT MEMORY ACCESS : 01, INTERRUPT REQUEST : 05
- Select CANCEL twice to close the DEVICE MANAGER and return to CONTROL PANEL. Close it too.
SETTING THE GAME TO RUN WITH YOUR SOUND CARD
- Go the BC3000AD v2.0 group and select the SOUND SETUP icon
- At the SOUND SETUP screen, use the ARROW KEY and move down to the SELECT DIGITAL button.
Press ENTER to reveal the list of supported sound cards. If you see your card listed, then use
the ARROW KEY to select it from the list and press ENTER. If it is not listed, then, select one
of the Soundblaster cards, starting with the SOUNDBLASTER 16/AWE32. Why? Because most sound cards
today, have emulation for one Soundblaster brand or another.
- After selecting a sound card, the PORT field will be displayed and a default setting
selected. If the setting matches what you wrote down as the INPUT/OUTPUT range above, i.e. 220,
then press ENTER. Otherwise, use the ARROW KEY to select the proper setting, then press ENTER.
At the DMA field, select the setting you wrote down for the DIRECT MEMORY ACCESS, then press
ENTER. At the IRQ field, select the setting you wrote down for the INTERRUPT REQUEST, then press
ENTER.
- The TEST button will now be highlighted. Make sure that your speaker volume is up and then
press ENTER. If you hear the digital test sound, press ENTER to get rid of it. If not, go back
and check the settings again or try another Soundblaster emulation and repeat these steps.
- When you are done testing, use the ARROW KEY to move to the OK button and press ENTER.
- At the SOUND SETUP screen, use the ARROW KEY and move to the SELECT MIDI button. Press ENTER
to reveal the list of supported sound cards. As indicated above, select your sound card from the
list or a Soundblaster emulation. This time for the PORT, use the second set of INPUT/OUTPUT
range that you wrote down. For MIDI, these range from 330 or 388 all the way up to 620 or higher.
This range will NOT match the range of the DIGITAL setting. This makes it easy to tell which to
use. So, for instance if second set of ranges you noted was 0388-038B or 0330-0331, you can use
either 388 or 330 as the PORT setting.
- The TEST button will again be highlighted. Press ENTER. If you hear the MIDI test sound,
press ENTER to get rid of it. If not, go back and check the settings again or try another PORT
setting.
- When you are done testing, use the ARROW KEY to move to the OK button and press ENTER.
- At the SOUND SETUP screen, use the ARROW KEY and move down to the OK button and press ENTER
and then again when prompted to save the settings.
Your sound card is now configured. As long as the digital and MIDI sound tests played OK in
this Sound Setup program, sound will also work in BC3K.
Due to some incompatibilities, you may have to disable MIDI if you experience loss of sound
or unexplained crashes when running the game. You can do this from within the game using the
CONFIG program.
Q. I HAVE A PCI PLUG 'n PLAY SOUND CARD, HOW CAN I CONFIGURE IT?
A. Though the HMI sound system used by BC3K supports a lot of cards, there are some obscure ones
that are not supported. For instance, this example shows you how to hack it so that you can
make it work. No matter what card you have, if it does not have Sound Blaster DOS legacy
support or at least emulation support, it will NOT work.
ESS AUDIODRIVE ON COMPAQ PRESARIO 2240 EXAMPLE
- Go into CONTROL PANEL and from the SYSTEM/DEVICE MANAGER tab, select the 'sound, video and
game controllers' tab. This should now open to reveal the sound card. Left-click on it and then
select the RESOURCES tab. Scroll the list and make a note of the 'interrupt request', 'direct
memory access' and 'input/output range' values. For the ESS card, you would have written
down IRQ 5, DMA 5, IO 220 (depending on your machine of course).
- From a full screen DOS session, go to the BC3K install directory and run SETUP.EXE for the
HMI sound system. Select the 'select digital' option and select all the defaults. You will not be
able to enter an IRQ. Do NOT test it. Click on OK to return to the menu. Go to 'select midi' and
do the same. Again, do NOT test it. Select OK to return to the menu. Finally, scroll down and
select OK to exit the menu and OK again to save the config.
- Using C:\WINDOWS\NOTEPAD.EXE or similar text editor, open up the HMISET.CFG file in the BC3K
install directory. Make sure you set NOTEPAD to view all files because it defaults to *.TXT. With
the file open, it should look like BEFORE version below.
BEFORE AFTER
[DIGITAL] [DIGITAL]
DeviceName = ESS AudioDrive DeviceName = ESS AudioDrive
DeviceIRQ = -1 DeviceIRQ = 5
DeviceDMA = 1 DeviceDMA = 5
DevicePort = 0x220 DevicePort = 0x220
DeviceID = 0xe019 DeviceID = 0xe019
[MIDI] [MIDI]
DeviceName = ESS AudioDrive DeviceName = ESS AudioDrive
DevicePort = 0x388 DevicePort = 0x388
DeviceID = 0xa002 DeviceID = 0xa002
Simply replace the DeviceIRQ, DeviceDMA and DevicePort values to match your card. In the case
of the ESS AudioDrive in the Compaq, it would now look like the AFTER version above.
- Save the file. Run the BC3K Sound Setup program and test the card. Do NOT change ANYTHING.
Just test it and then exit.
You can now start BC3K and be able to hear digitized sound and music. If you had previously
disabled soundfx in CONFIG, you need to go back there and enable it.
Using the above method, you can configure any sound card, even if it's not listed in the
SETUP program. You can also take a look at the SETUP.INI file for a list of supported cards,
their default values as well as their DeviceID. For most cards, you should be able to get
away with selecting a Soundblaster 16 or Pro emulation in the SETUP progam. If you cannot
enter your PORT, IRQ and DMA values because SETUP won't let you, then simply select the card
anyway and then put the values in the HMISET.CFG file as described above.
Q WHY CAN'T I GET MY PCI SOUND CARD TO WORK?
A BC3K is a primarily a DOS game and the sound setup will support ISA sound cards as well as PCI
sound cards with Legacy support in the motherboard bios. If your bios does not support it,
then you will not be able to configure the sound to use your PCI card in DOS legacy mode. This
happens with some VIA and ALI chipsets on motherboards such as Asus. These do not
have Non Maskable Interrupt (NMI) support in their BIOS. Some boards, including some earlier
ASUS boards, require a BIOS upgrade for any sort of PCI sound card to work. When in doubt,
make sure that your machine has the latest BIOS revision.
For instance, the Soundblaster PCI-64, PCI-128 and the Live! cards emulate the SB Pro and SB
16 cards in Legacy mode only if Non Maskable Interrupt (NMI) is available in the BIOS.
MONSTER SOUND II MX-300 OR AUREAL SQ1500/SQ2500 EXAMPLE
- If you have any of these cards, then, go into your Control Panel device manager and and make sure
the SOUNDBLASTER PRO EMULATION is enabled and there is no warning yellow icon next to it indicating a
conflict. Check in the PROPERTIES tab and make a note of the settings.
- Make sure that this file C:\WINDOWS\AU30DOS.COM is loaded in your AUTOEXEC.BAT when the
system starts up. Without it, DOS emulation won't work.
Watch and see what is displayed when this file is loaded at reboot. It will tell you whether or
not Soundblaster Pro emulation is enabled or not and the current settings.
- Once you have restarted the machine and verified that SBPRO emulation is enabled, run the
BC3K Sound Setup program and select the SoundBlaster Pro card for Digitized and the MPU-401 for
MIDI music. Make sure to enter the values for your card (as indicated above) and then run the
TEST program to make sure it works.
Setting up this card for SBPRO support, automatically added this lines to my AUTOEXEC.BAT
file:
LH C:\WINDOWS\AU30DOS.COM
SET BLASTER=A220 I5 D3 T4
I then had to manually change the default DMA for the SBPRO from 1 to 3 from inside the BC3K
Sound Setup program because DMA 3 is what the WIN98 system set the emulation mode to when I
installed my MX300 card.
SOUNDBLASTER LIVE! EXAMPLE
This card comes with excellent support for Soundblaster 16 emulation. You must install it
after you have installed the WIN9x component. For further info, refer to the extensive
SBLive! DOS setup file which contains detailed info on setting up SB16 support.
It contains extensive instructions on how to get DOS legacy support working for your card. You
will find the tips in Appendix B. You will need the Acrobat reader to view this file.
Once you have setup the legacy support, you can run the BC3K Sound Setup program and either
select the Sound Blaster 16 card with the default settings, or change the settings to match
your card's Sound Blaster 16 emulation settings. For MIDI music, you can choose the MPU-401
for better MIDI sound quality.
When I installed SB16 legacy support, SBLIVE! included these lines in my AUTOEXEC.BAT file
SET BLASTER=A220 I5 D1 H5 P330 T6
SET CTSYN=C:\WINDOWS
C:\PROGRA~1\CREATIVE\SBLIVE\DOSDRV\SBEINIT.COM
NOTES:
- The SBLIVE! SB16 DOS legacy support defaults to IO:220, DMA:1/5, IRQ:5
Q. HOW COME MY PCI SOUND CARD SETTINGS ARE NOT SUPPORTED IN THE BC3K SOUND SETUP PROGRAM?
A. You have to ensure that your PCI sound card's settings can be supported in the BC3K sound
setup. For instance, the SB 16 is only supported with IRQ 2,5,7,10. If your system has it
setup for say, 9, it will not work. You will have to go into Control Panel and free up one of
those IRQs or go into your BIOS and reserve the desired IRQ for use by the card.
For instance, someone had a problem getting the SB Live! Value card to work. The install
program had set the SB 16 emulation to use IRQ 9 which is not supported. This is what he had
to do to get it to work.
- Updated the BIOS from the Asus website
- Reserved IRQ 5 in the BIOS for use by Legacy devices
- Removed the SB Live! card via Control Panel. Then rebooted the machine which caused WIN98 to
autodetect and reinstall the Live! card. This time the SB 16 emulation in Control Panel was set
to IRQ 5 instead of the previous IRQ 9.
- Went into the Sound Setup program and setup the DIGI and MIDI options of the SB 16 card
according to the new settings. It worked!
DOS LEGACY RESOURCE CONFLICTS
Sometimes, no matter what you do, there will probably be a conflict with the card's Sound
Blaster legacy support resources. In which case, you will have to change the order in which
your cards are inserted in your motherboard slots, especially if your motherboard has an AGP
slot.
I ran into this problem with the Monster MX300. No matter what I did, I could not get the
Sound Blaster Pro emulation resources to be freed up. It kept conflicting with my SCSI and
network cards. So, after doing some research, I had to physically move my cards around and
then everything worked fine. This was because slot 4 where the MX300 was, shared the IRQ
resources with my USB and SCSI controller. Since I couldn't change the SCSI resources because
it is built into the Asus P2B/LS motherboard, I had to move cards around. USB is
not a big deal because it behaves ok. However, if you don't have any USB devices in your
machine, it is advisable to disable it in your BIOS by preventing it from using an IRQ. This
will free up one more IRQ for you to use. This may not seem like a big deal because the PCI
specifications allow devices to share resources, however, sometimes even this can cause
problems and especially with DOS legacy devices.
Here is the layout of an Intel PII-400 development system with the ASUS
P2B/LS motherboard. Uses the Award BIOS and Intel 440BX AGP/PCI chipset.
AGP - STB Velocity 4400 16MB 2D/3D video card
PCI1 - Diamond SupraMax 56i modem [ IRQ:10 ]
PCI2 - Diamond MX300 Aureal 2.0 3D sound card [ IRQ:5 ]
PCI3 - 3Dfx Voodoo2 12MB 3D video card
PCI4 - 3Dfx Voodoo2 12MB 3D video card
ISA1 - Surfboard cable modem [ IRQ:11 ]
Here is the layout of an AMD K6-2/350 development system with an
EPOX EP-51MVP3M-M motherboard. Uses the Award BIOS and VIA Apollo AGP/PCI
chipset.
AGP - 3DFX Voodoo3 16MB 2D/3D video card [ IRQ:11 ]
PCI1 - Adaptec AHA-2940 SCSI controller [ IRQ:11 SCSI:7 ]
PCI2 - Linksys 10/100 10-BaseT Ethernet NIC [ IRQ:9 ]
PCI3 - Soundblaster Live! [ IRQ:12/5 ]
PCI4 - Soundblaster PC-DVD decoder card [ IRQ:12 ]
ISA1 - USR Robotics Sportstar 56K modem [ IRQ:3 ]
WARNING:In general, the PCI specs has resources shared as follows. In my case, I
originally had the MX300 card in PCI slot 4, so I moved it to slot 2 and the problem was
solved. Though AGP/PCI cards can share resources, there are cards and devices that just refuse
to get along and you have to delve in your system BIOS to reserve resources. To make things
worse, these seem to also vary with BIOS and AGP/PCI chipsets. As you can see from the
above, the Epox and Asus boards, use different BIOS and AGP/PCI chipsets.
PCI slot 1 - shares with AGP slot
PCI slot 4 - shares with USB & SCSI
JOYSTICK PROBLEMS
Q. WHY CAN'T I USE MY JOYSTICK?
A. BC3K does not support digital joysticks in native mode. You can either select one of the
sticks it supports from the chart below, or you can create a profile. For instance, when using
the MS Sidewinder PRO, you can select the CH F16 Combat Stick.
Also, if you select the incorrect joystick in CONFIG, you will be greeted by a black screen
and the program will hang on startup. To solve this problem, delete the SETUP.CFG (which
stores the joystick type) and the JOYSTICK.SET (which stores the joystick settings). Restart
the game. You will then have to go back into CONFIG and reconfigure your settings.
If your joystick drifts while in the game, disable the auto-pilot and then type [CTRL+J] to
re-calibrate it.
If your stick is not supported in the CONFIG menu, use this chart to determine which
compatible stick to use based on the features of your stick.
BUTTONS THROTTLE HAT
2 button stick 2 no no
4 button stick 4 no no
Thrustmaster 4 no yes
CH Flight Stick 2 yes no
CH Fighter Stick 4 yes no
CH Flight Stick PRO 4 yes yes
CH F16 Combat Stick 4 yes yes (2)
TO CREATE A JOYSTICK PROFILE
- Go into windows explorer, into your BC3K directory, and delete a file called JOYSTICK.SET if
it exists.
- From Windows 95/98, go to the Game Controller icon in the Control Panel.
- Click on the ADVANCED section and then select CHANGE. Scroll until you find the Thrustmaster
Flight Control System and then double-click on it.
- Calibrate it and restart the game.
- Select CONFIG from the BC3K MAIN MENU and select Thrustmaster.
- Exit and calibrate the stick when prompted
- When you launch and you are in the cockpit or bridge, press [CNTRL+J] to calibrate the stick
if it behaves erratically.
CREATING A JOYSTICK PROFILE FOR SIDEWINDER JOYSTICKS
- Go into windows explorer, into your BC3K directory, and delete a file called JOYSTICK.SET if
it exists.
- Start the Microsoft Profiler software and choose New from file menu
- Click on Settings tab and change emulation to Thrustmaster
- Save as a unique name, i.e. BC3K.
- Activate the newly created profile by clicking on it.
- Select CONFIG from the BC3K MAIN MENU and select a stick from the chart above
- Exit and calibrate the stick when prompted.
- When you launch and you are in the cockpit or bridge, press [CNTRL+J] to calibrate the stick
if it behaves erratically.
NOTES:
- You can also, instead of using the Thrustmaster emulation (which won't let you use the
throttle on some SIDEWINDER sticks, select the CH F16 COMBAT STICK from the CONFIGURE menu. This
configuration allows you to use the 4 primary buttons, throttle and hat switches on your
SIDEWINDER PRO.
CREATING A JOYSTICK PROFILE FOR THE LOGITECH WINGMAN EXTREME
- Go into windows explorer, into your BC3K directory, and delete a file called JOYSTICK.SET if
it exists.
- Go into control panel, game controllers, and select Wingman Digital Extreme
- Reboot the system
- Go into control panel, Logitech Entertainment System and select BC3K from the menu. Hit
APPLY, but DO NOT SHUT DOWN LOGITECH ENTERTAINMENT SYSTEM! Just minimize it.
- Fire up BC3K, and it should ask you to calibrate your joystick.
- If you have another type of Logitech stick, then select a stick from the chart above.
NOTES:
- You can also bypass this method and select one of the sticks listed in the chart above
depending on the buttons, throttles and hat switches on your particular Wingman joystick.
CREATING A JOYSTICK PROFILE FOR SAITEK JOYSTICKS
- Download the Saitek Config files. Included is a text file showing you how to set it up.
This file does NOT support the Cyborg 3D stick.